Glossary of Electric Bike Terms
Edward Benjamin, Senior Managing Director of eCycleElectric Consultants LLC.
AC Current – alternating current is used in electrical mains, but very rarely in Light Electric Vehicles.
Advanced Battery – a battery using NiMH or Lithium cells. Usually requiring a battery management system (BMS). Higher performance and higher cost.
After Market Kit – a kit of components to convert a manual bicycle to an electric bicycle.
Amp – From Ampere, which is a measure of the amount of electrical current that passes a given point in a given amount of time. Used to describe the demand or supply of energy.
Amp Hours or AH – a measure of energy that is equal to the amount of energy that passes a given point in an hour. Usually used to describe battery capacity. For a more exact definition please see Barrie Lawson’s comment at the end of this post.
Auxiliary Battery – is a battery that can supply current to the vehicle, but is optional, or extra, or added on.
Battery, or Energy Storage Device – is a combination of cells that create a specific voltage and current capability to power an electric motor or vehicle.
Battery Box, or Battery Package – the combination of cells that comprise a battery that provides electrical energy for the vehicle. Packed into the unique form factor for a particular vehicle. Often with BMS or motor controller inside the same box.
BMS– Battery Management System is an electronic circuit that is found on advanced batteries.
The BMS prevents damage to the battery, and prevents safety problems of battery overheating and monitors the state of charge.
Brushless DC Motor – longer lasting and simpler than a brush type motor. There are no wear points other than the bearings. But more costly in terms of control electronics. Also called a BLDC Motor.
Brush Type DC Motor – uses brushes in the motor, which creates a wear point. But less expansive in terms of control electronics and manufacture.
C-Rate – is a unit of measurement that describes how fast a battery can supply current. A 1c rate means that the battery can be completely discharged in one hour. Trying to go faster than that will simply not work or might damage the battery. A 2c rate battery can be discharged in 30 minutes, or twice as fast as a 1c rate battery. This is important in regards to the power that can be developed by the motor attached to that battery. For example, a 500 watt motor that is climbing a hill might demand 30 amps of energy. If the battery is a 10 ah battery, then it must supply energy at a 3c rate to allow the motor to do it’s job. If the battery is only capable of 1c, the rider is likely to be walking this hill.
Cells – individual electro chemical devices that create electric current and are combined into packages to provide appropriate voltage and current for a specific function … called “batteries”.
Ceramic Magnets – used in electric motors. Lower in performance and cost than Neodymium magnets.
Connectors – the fittings that allow the electrical components and wiring to be connected. Often easily unplugged or released.
Coulombs – are units of measurement of energy. The amount of energy equal to one amp for one second. Thus there are 3600 coulombs in one Amp Hour. Since battery state of charge for lithium is difficult to determine by measuring voltage, sophisticated BMS measure SOC of Lithium batteries by coulomb counting. For a more exact definition please see Barrie Lawson’s comment at the end of this post.
Current – a flow of electricity – usually refers to the amount of electrical energy being used by the vehicle.
DC – direct current, or the form of electrical current used in nearly all LEVs.
DC Motor – a motor that uses Direct Current.
DIY Kit – a set of components to convert a manual bicycle to an electric bicycle.
Ebike – generic term for electric powered bikes, but in many cases meaning an electric bike that is controlled by a throttle rather than by the riders effort. (See Pedelec)
Electric Bicycle – a vehicle that is regarded by local law, wherever that may be, as a “bicycle”, with the rights and responsibilities of a manual bicycle. But having an electric motor and battery to assist the rider.
EPAC – Electric Pedal Assist Cycle or what European Union law calls an electric bike.
Hub Motor – an electric motor located in the front or rear hub.
Human Electric Hybrid – an electric bicycle that allows both human and electric power. A very efficient system as humans are high torque, low endurance devices and electric motors are lower torque, high endurance devices limited only by the battery. Together they are a very efficient and useful propulsion system for a vehicle.
ICE – Internal Combustion Engine – the propulsion device in petrol powered vehicles. A source of expense, pollution, noise, and political fuss.
Low Speed Electric Assisted Bicycle – what USA law calls an electric bike.
Lithium Battery – an advanced battery that has excellent performance, weight, and life characteristics. But comes in several variants such as Lithium Manganese (3.7V), Lithium Iron Phosphate (3.3V), and others. All lithium batteries are flammable and need a BMS and conscientious manufacturers / testers to reduce fire risk to users, dealers, freight carries. Lithium battery fires get a lot of press, but are actually very rare.
Max Discharge or Max current – refers to the discharge rate of the battery. See C rate.
Manual Bicycle – propelled only by human power – a very old paradigm, like sails, or manual typewriters, or writing with charcoal on a slate.
Motor Controller – An electronic circuit that controls the speed of the electric motor, as well as various other functions depending on the model and features of vehicle.
Motor – an electric motor that assists the rider. Can be located in various places and manners.
Pb or Pb A Batteries – refers to Lead Acid Batteries.
Neodymium – a rare earth metal that is used for the production of high energy permanent magnets. Such magnets are commonly found in LEV motors, and are a source of considerable cost.
Ni Cad – Nickel Cadmium batteries, not used for some time by electric bikes but found on some older models. Toxic and lower in performance than NiMH and Lithium. (1.2V)
NiMH Battery – Nickel Metal Hydride battery – non toxic, higher performance than Lead Acid, less performance than Lithium. Not common, but found in some ebikes. (1.2V)
PAS Bike – a Pedal Assist System bike, usually designed for the Japanese market and using a proportional power paradigm – the motor delivers additional power in proportion to the effort being exerted by the rider. PAS is a Yamaha patent.
Pedelec – an electric bicycle where the rider must pedal for the motor to run. Variants of this are the PAS paradigm used in Japan, and the EPAC paradigm used in Europe.
Permanent Magnet – a magnet that stays magnetized without external supplies of energy. These are used in almost all motors use on LEVs.
Push to start, or Pedal to start – some ebikes require the user to pedal a few strokes or gain a certain speed by pedaling before the motor can be activated.
Speed Sensor – is a device that detects rate of pedaling and is used to activate power in pedelecs. Not as nice a “feel” as a torque sensor system.
SOC – State of Charge is the “gas gauge” or how much useable energy is in the battery. Seemingly a simple task, this can be critical to user satisfaction and can be complex to establish.
SVRLA – Sealed Valve Regulated Lead Acid batteries are the most common type of ebike and e scooter battery today.
Electric Vehicle Outfitters system is still in production.
Throttle – a device operated by the user to control the speed of the vehicle. Can be twist grip, thumb operated, or other methods.
User Interface – the interaction of the user and the machine which includes controls, seat, pedals, but usually refers primarily to the data display of information like speed, distance, SOC. Rapidly becoming interactive with the internet and GPS via phone and other devices.
Vehicle Controller – an electronic circuit that monitors and regulates the motor controller, user interface, battery management system and other features.
Volts, Voltage – refers to the force that a given level of electrical flow can exert. The scientific definition is complex, but see “Benjamin’s electricity as water”.
Watts – refers to a unit of measurement of how much work is done. This can be used for electrical, muscle, or ICE applications (and more). But for LEV use, watts refers to how much work is being, or can be accomplished by the system or device. For example a 500 watt motor is capable of twice the work of a 250 watt motor, if all else is equal. A human in really good condition will create about 75 watts of work over an extended period. Athletes can do better, usually for short periods. One horsepower is about 750 watts. For a more exact definition please see Barrie Lawson’s comment at the end of this post.
Watt Hour – is a measurement of energy usually used to describe battery capacity for LEVs. The formula that applies is to multiply volts times AH and this will give you watts. A Kilo Watt (1000 watts) is a pretty big battery that might be found on a motor scooter, while a pedelec may have about 360 watt hours in it’s 36 volt by 10 AH battery.
Wiring Harness or Harness – the wires, connectors and switches that carry electrical current and signals about the vehicle.
End of Glossary of Electric Bike Terms.
BONUS! Ed Benjamin’s Electricity as Water explanation – Since the author was originally trained in Biology and is not good at math, the following model was established to explain electricity on an electric bike in the early days of his career:
Think of electricity as water. A can of water (cell) is the battery and is the supply of water to the vehicle. The size of the filler hole on top of the can is the ‘rate of charge’ or how fast we can add water (energy). A bigger hole means a shorter recharge time. The hole on the bottom of the can is the ‘C rate’ or maximum current. The bigger the hole, the more current is available. Different batteries have different sized holes on both top and bottom.
The speed or pressure at which the water will flow out of the can is the voltage – or potential to do work. Higher pressure can move a motor faster or with more torque. Think of voltage as how powerfully the can will empty itself.
Amp hours describe the size of the can. Amps and coulombs describe the drops and globules of water.
A battery is a collection of cans, and a battery management system is a system of valves and microchips that controls the piping serving the cells and allows them to all work together, safely and efficiently. The more cans, the higher the voltage or force of water that can be supplied.
A motor controller is needed because if we hooked the water supply (energy supply) up to the motor with nothing else, the motor would spin as fast as it can, and use all the water very quickly, overheating and maybe failing as it does so. A motor controller turns the current (water) supply on an off to control how fast the motor turns. Thus controlling speed and rationing the water supply.
The wiring harness is the piping that takes the water (current) to the places where it is needed. Switches are on / off valves.
This model is not complete, but hopefully it will help some readers. The idea is not unique to Mr. Benjamin, but he wrote this version.
Thank you to Edward Benjamin, (Senior Managing Director of eCycleElectric Consultants LLC) for this thorough electric bike terms post.
P.S. Don’t forget to join the Electric Bike Report community for updates from the electric bike world, plus ebike riding and maintenance tips!
[…] Enhance your e-bike education with this glossary of electric bike terms! […]
[…] Glossary of e-Bike Terms […]
[…] Glossary of Electric Bike Terms […]
Barrie Lawson says
I have made additions to my earlier comment which hopefully makes things even clearer.
June 19, 2013 at 5:17 am #
I have not checked every entry but please note the following:
AmpHours and Coulombs are both measures of Charge not Energy.
The Energy depends on the voltage applied when the current is flowing.
The Unit of Energy in this case is the WattHour.
Note also that the Watt is not a measure of the Work Done. The Watt is a measure of Power which is the Rate of doing Work.
Energy is the capacity to do Work. It has the same units as the Work Done.
The Joule is also measure of Energy AND Work Done.
1 WattHour = 3600 Joules of Energy
When you purchase Energy from the Electricity Utility (AC in this case) 1 so called “Unit” is 1 KiloWattHour, that is 1000 WattHours
See more details at
Your comment is awaiting moderation.
– See more at: https://electricbikereport.com/glossary-of-electric-bike-terms/?goback=%2Egde_65337_member_251052398#sthash.d5TWKcKB.dpuf
David McDougal says
Thanks to both Edward Benjamin and Pete. This is excellent: clear, brief, sans hype. Would that there was more such information in this space.
Ed Benjamin says
Barrie, I am tickled that I am being corrected by such a qualified authority. as a prominent expert on batteries, you know more about these things than I will ever learn. I was trying to keep this glossary simple to an extreme. Maybe I should add your comment as a more exact definition if Pete can do so.
Savannah eBikes says
This is why I stay subscribed, Pete… Awesome post! Clear and to the point.